How do I program my 2005 Grand Prix remote?

Press and hold the fob’s “lock” and “unlock” buttons at the same time for 14 seconds. After you’ve held it seven seconds, you will hear a chime confirming successful programming. Wait the 14 seconds for a second chime. Repeat the last step for each additional remote.

How do you program a key fob for a 2005 Pontiac?

2005 Pontiac Montana Key Fob Remote Programming Instructions

1. Remove the key from the ignition.
2. Remove the “BCM PRGRM” fuse from the fuse panel.
3. Close all of the doors.
4. Close the lift gate.
5. Insert the key into the ignition, and turn to the ACC position.
6. Turn the key to OFF and then back to ACC within 1 second.

How do you program a keyless remote for a 2006 Pontiac Grand Prix?

Press down and hold the “Unlock” and the “Lock” buttons at the same time. Continue to hold them for 14 total seconds, during which you will hear two chimes; one at seven seconds and one at 14 seconds. These two chimes indicate that the remote is synchronized and programmed, respectively.

How do you program a key fob for a 2004 Pontiac Grand Prix?

Press and hold the LOCK and UNLOCK buttons for 14 seconds, listening for the chime. Wait 14 seconds for the second chime. Repeat this step for all additional remotes, remove the key, replace the fuse, and exit the car. You will have programmed the remotes.

How do you program a key fob without the original?

How to program a key fob

1. Replace the batteries inside the key fobs.
2. Get inside the car.
3. Turn on the ignition.
4. Press the lock button on the remote key.
5. Listen for a Lock Sound.
6. Programming additional remotes.
7. Turn off the ignition.
8. Step out from your car and test the result.

How do you program a keyless entry for a 2004 Pontiac Grand Prix?

Put your key into the ignition, and turn to “ACC.” Turn the key on and off within a second. Open and close the driver’s door and listen for the chime that indicates you are in programming mode. Press and hold the LOCK and UNLOCK buttons for 14 seconds, listening for the chime. Wait 14 seconds for the second chime.

How do you program a new key fob for a 2007 Pontiac Grand Prix?

How do you program a key fob for a Pontiac Grand Am?

PRESS and HOLD the LOCK and UNLOCK buttons on the first remote to be programmed for 15 seconds until the vehicle chimes twice indicating successful programming of the remote. REPEAT Step 9 for any additional remotes to be programmed, including working ones. REMOVE key from Ignition to EXIT Programming Mode.

Can You program a Pontiac key fob?

Pontiac does include programing instructions for the Aztek, Vibe, and Montana, but not for the Bonneville, G6, Grand Am, Grand Prix, Montana SV6 or Sunfire models. These models require you to go to a Pontiac dealership or a licensed Pontiac vendor such as an automotive locksmith to program your key fob.

How do you program a Ford Ranger key fob?

While holding the door lock, insert the key twice without turning it. Insert it a third time and leave the key in the ignition. Release the door lock. A chime will sound three times to let you know that you are in programming mode. Press both the “lock” and “unlock” buttons on the remote for about 30 seconds.

How do I unlock my 2005 Pontiac Aztek with key?

Enter your 2005 Pontiac Aztek. Close all doors. Press and hold the “unlock” button on the driver’s door. While holding the door lock, insert the key twice without turning it. Insert it a third time and leave the key in the ignition. Release the door lock.

Can the dealer program a new remote on a Grand Prix?

While the dealer can program a new remote for you, it probably won’t be free. You can do it yourself and save the money in just a few minutes. Locate the fuse box under the dash of your Grand Prix, just inside the driver’s side of the car.