What size belt does a Swisher pull behind mower take?

74-Inch
Swisher 4220 74-Inch Belt – Fits select Swisher 44-in, 42-in and 22-in Mowers.

What size belt does a Swisher 60 inch mower take?

122-Inch
Swisher 5058 122-Inch Belt – Fits select Swisher 60-in Trailmowers and ZTR Mowers – Black/Blue.

How do I know what size lawn mower belt I need?

Place one end of the tailor’s tape measure on the mark, then extend the tape measure around the inside circumference of the circle until you reach the mark with the other end of the tape measure. Take your reading from the tape measure to determine the size of the belt.

What size belt do I need for a 52 inch deck?

Exmark Deck Belt fits 52″ Cut Decks No. Size: 5/8″ x 141-1/4″. Replaces part number 413308 and 1-413308.

Are all 42 inch mower belts the same?

There’s no standard size for a 42-inch-cut riding mower. Each model uses a different size belt. To give examples, some models use a drive belt that is ½ inch wide by 92 inches in length, while others use a belt ½ inch wide by 85 inches in length.

What size belt does a 42 inch deck take?

Cub Cadet Deck Belt fits 42″ Cut Decks No. Size: 1/2″ x 66-3/4″. Replaces # 954-0645 and 754-0645.

How do you start a 24 Swisher predator?

BEGIN CUTTING Make sure that all guards, belt guides, and the spark plug wire are properly attached. Start engine, set engine throttle control at maximum engine idle speed for best results. Allow engine to run a few moments and slowly engage blade. Move transaxle into low gear and activate “GROUND CONTROL” lever.

Where is the model number on a Swisher?

Finding Your Model or Serial Number Every Swisher product has a model and serial number on a silver decal.

What size belt does it 42 inch deck?

What size is a 42 inch belt?

MEN’S BELT SIZING

BELT SIZE IN INCHES	BELT SIZE IN CM	MEN SIZES
36	92	M
38	97	M
40	102	L
42	107	L

What size is a CRAFTSMAN 42in deck belt?

Dimensions:

Dimensions:
Length :	101.5 (in.)
Width :	0.5 (in.)

How do you start a Swisher trimmer?

To start the trimmer: Pull control bail against the handle and hold. Push primer button on engine as directed. Pull back sharply on recoil starter handle. Begin trimming.

How long is a 144959 belt?

Size Considerations A 144959 V-belt has only one size, and spans a half-inch in width and 95.5 inches in circular length.

How do I know my belt size?

An easy way to determine belt size is to simply “add 2″ to your off-the-rack trouser size. For example, if you wear a 36” waist trouser, then a 38 belt size will be a safe bet. Most will find this simple formula works best for pants worn at a traditional height–close to the natural waistline.

How long is a 42 inch mower Deck Belt?

Mower Deck Belt fits 42″ Mowers built 2006. (Dimensions 1/2″ wide X 101 1/4″ Long).

How do you put line on a Swisher trim and mow?

Loosely fold trimmer line in half. (1) Place loop of line against outside of loop on the trimmer head. (2) Bring ends around and through the loop and over the trimmer line loop. (3) Pull ends to tighten loop.

How long is an Ariens 42 Deck belt?

95.50
Dimensions

Belt length (in.)	95.50	42 in.
Fits Deck Size (in.)	42 in.	42
Product Depth (in.)	0.37	95.5
Product Width (in.)	0.5

How do I choose the right belt?

How to Choose the Right Size Belt. Your belt size should be 1-2 inches longer than the size of your pants waist. So if you take a 40 in pants, you want a 41-42 inch belt. Alternatively, you can work out the size of your new belt from your old belt.

How do belt sizes work?

Your belt size is two inches larger than your pant waist size. If you wear a 34″ trouser, buy a 36″ belt. If your waist size is an odd number, buy a belt three inches larger instead of two. Most belts have five holes.

What size deck belt do I need for a 42 inch deck?

AYP / Craftsman / Sears 42″ Deck Belt No. Size: 1/2 x 101-1/2. Replaces part number 429636.